BSA Bantam Spares

Click here to edit subtitle

New Pattern Parts....
Part numbers for reference only.

email:- [email protected]

TD001 Engine timing disc D10/D14 etc.

Highlighted 16.5 degrees, rigid perspex ........................8.00

01-4606 Screw, 2BA x 1/2" ............................................0.30

02-0498 Screw, gearbox oil seal holder..........................0.55

19-0260 Points cam Wipac replica....................Out Of Stock

19-0268 Magneto bush Wipac generator........................2.40

19-8649 Rear drive chain 120L or to spec.....................29.50

21-5102 Nut; alternator stud..........................................0.35

21-5103 Nut, 5/16 BSF...................................................0.20

24-0732 Bearing L/H crank shaft C15 etc.......................8.75

24-7178 Screw 1/4" bsf..................................................2.65

29-2023 Nut, Magneto D10-D14 etc...............................3.85

29-2089 Nut, Oil pipe union. A65/B25/44.......................1.65

29-3412 Gearchange Lever 3 speed C10L C11G..........17.50

29-3857 Bearing, high gear, C15.....................Use:- 57-0665

29-5156 Kick start pedal bolt. A65/D1-3.........................3.40

40-0025 Crankshaft oil seal C15/B40.............................3.55

40-0026 Layshaft bush C15.........................................13.70

40-0030 Camshaft bush, early C15................................6.30

40-0042 Crankshaft bearing sleeve..............................16.35

40-0063 Small end bush C15 (se142)..........................12.15

40-0088 Piston ring set +020" C15...............................31.60

40-0091 Piston ring set +040" C15...............................31.60

40-0100 Push rod C15......................................each.....9.65

40-0111 Sump plate gasket C15/B40.............................0.80

40-0118 Woodruff key....................................................1.65

40-0124 Rockerbox stud C15/B40, 2-3/4".......................1.10

40-0126 Cylinder base gasket C15................................1.00

40-0127 Rockerbox stud C15/B40 3"..............................1.25

40-0127A Rockerbox stud (head steady one).................1.25

40-0129 Rockerbox stud C15/B40 3"..............................1.10

40-0131 Rockerbox stud C15/B40 2-1/4"........................1.25

40-0133 Valve guide +010" C15.....................................6.65

40-0140 Head gasket C15............................................13.60

40-0162 Nut, Rockerbox oil feed pipe.............................1.95

40-0163 Tappet screw C15/B40......................................4.25

40-0165 Valve, Inlet.....................................................10.40

40-0166 Exhaust valve C15..........................................19.85

40-0167 Valve cotter C15...............................................1.20

40-0168 Valve outer spring...................................set.....9.25

40-0170 Valve spring bottom cup C15............................5.90

40-0171 Valve spring top collar......................................2.75

40-0174 Push rod tube (alloy)......................................22.60

40-0183 Rocker oil feed pipe C15/B40/B44/B50...........27.70

40-0270 Rocker cover gasket C15..................................1.30

40-0217 Crankcase oil feed pipe C15...........................10.00

40-0222 Camshaft bush C15/T20...................................9.60

40-0223 Layshaft bush C15...........................................8.25

40-0235 Cover screw 1/4 x 3/4"......................................0.90

40-0241 Sprocket cover gasket......................................0.90

40-0243 Oil seal rear of clutch C15/B44/B50..................1.85

40-0246 Clutch back plate screw C15............................0.55

40-0688 Points cover gasket C25, B25...........................1.95

40-1033 Gearbox dip-stick (plastic)................................6.75


40-2760 Silencer C15/B40 1959 onwards.....................65.00
40-3025 Kick start pawl C15/T20....................................2.60

40-3059 Kickstart quadrant 5/8" shaft '63-'69...............98.00

40-3073 Gear Change Lever C15 / B40 / T20 Cub........25.00

40-3220 Plain steel clutch plate C15/B40/B50................5.70

40-3231 Clutch spring C15 etc..........................each.....1.15

40-3271 Kickstart ratchet pinion...................................17.25

40-3279 Kickstart Ratchet C15/B44/TR25.....................14.95

40-8328 Oil tank filter C15 etc........................USE:- 82-3179

41-0214 Carb joint washer 1-1/8" tufnal ........................1.45
41-3045 Bush, high gear C15............................each.....4.20
42-2699 Heat shield Hi level exhaust............................12.65
42-8010 Side cover grommet.........................................3.45

57-0394 Roller ..............................................................0.30

57-0665 Bearing, high gear, C15...................................9.35

57-1164 T20 Cub Gear Change Lever............USE:- 40-3073

57-2764 Kick Start Lever A7 / A10 / A65.......................36.80

57-3868 Rigid kick start lever, Bantam large spline.......29.00

57-3981 Clutch pressure spring B175............................1.30

61-3188 Flywheel extractor Wipac................................10.50


61-3191 Clutch compressor tool all Bantams...............18.25

65-1417 Carb joint washer, inlet.....................................0.95

65-3062 Cover screw 2-1/4"................................out of stock

66-3058 Kick start return spring M20/M21 etc.................9.25

65-3428/5 Kickstart pedal spring clip. A65/D1-3.............1.75

65-3427 Kick start pedal top A10/ D1-3..........................9.15

67-0101 Piston circlip C15  A7/A75 triple...........each.....0.95

67-0133 Cover screw,

1/4 x 1" BSW zinc plated cap head...................each.....0.30

67-3342 Spring, selector shaft. D14/B175......................1.50

68-0216 Side cover screw 1/4 BSF x 2-1/4 ....................1.25

68-0222 Carb to barrel stud...........................................2.95


68-3193 Kick start rubber, rigid lever...............................1.75

68-3193/A Kick start rubber folding lever type.................2.80

68-7704 Screw, alternator cover D10/D14 etc.................1.25

70-4568 Oil seal C15 K/S shaft/Tri.T120 timing cover.....1.85 70-6026 Bearing circlip, Triumph ....................................0.95

70-7805 Standard piston kit 175cc twin ringed.............56.80

70-7806 +020" 175cc twin ringed piston kit..................56.80

70-7807 +040" 175cc twin ringed piston kit...................56.80

70-7808 +060" 175cc twin-ringed piston kit..................56.80

70-7819 Insulating washer, carb inlet.............................1.50

70-7822 Cylinder base gasket D14..................Use:- 90-1597

70-7882 Gasket points cover C25/B25/A65.....................1.95

70-7987 Gearbox filler bolt/plastic dipstick.....................6.45

70-8014 Bearing,high gear, C15....................................9.35

70-8768 Circlip, Triumph................................................0.50

70-9955 Circlip, G/Pin (eyed type) ....................each.....0.40

70-9998 Casing screw 1/4 BSF x 3/4 .............................0.90

71-1423 Gasket, points cover C25/B25/A65....................1.95

71-1462 Gasket.............................................................1.95

76-0219 Screw, outer cover............................................0.90

76-0546 Side cover screw  BSF.........................each.....1.25

76-7514 Cover screw.....................................................0.95

82-3179 Oil tank filter C15 etc......................................19.35

82-8291 Nut, front pipe...D14 Large bore.....................10.95


82-8293 Front down pipe D14/B175.............................45.00

82-8295 Exhaust sealing ring large bore........................2.25

82-8296 Exhaust pipe adaptor.....................................10.65

82-8417 Front pipe Hi level D14/Bushman large bore...38.50

89-3006 Gearbox sprocket oil seal D1, 3, 5, & 7.............2.45

89-3023 Main bearing .....................................................9.25

90-0009 Std Piston rings 125 cc....................................6.70

90-0010 Outer crank bearing.........................................2.90

90-0011 Mainshaft bearing 3 speed...............................3.50 

90-0012 Gearbox sprocket bearing................................2.50

90-0024 Circlip, Pinion ratchet.......................................1.25

90-0027 Circlip, clutch outer..........................................4.85

90-0030 Clutch spring cup ............................................3.35

90-0037 Steel driven plate.............................................4.80

90-0040 Spring retainer.................................................3.65

90-0046 Selector spring.................................................2.60

90-0047 Selector spring socket......................................6.80

90-0063 Lock washer, selector plate..............................1.00

90-0067 Bush, Gearbox main shaft...................each.....6.50

90-0068 Gearbox sprocket 15T.......................................8.65
90-0068/17 Gearbox sprocket 17T..................................8.50

90-0070 Lock washer, gearbox sprocket.........................1.40

90-0071 Gearbox sprocket distance sleeve....................7.30


90-0076 Bronze bush mainshaft clutch housing.............9.20

90-0083 Layshaft bush 3 speed.....................................9.20

90-0084 Gudgeon pin D1..............................................4.35

90-0085 Piston circlip D1-D3.............................each.....0.50

90-0088 Kick start shaft & quadrant small spline..........26.00

90-0089 Kick-start return spring.....................................8.25

90-0099 Clutch push-rod...............................................6.25

90-0109 Spacer tube, crankcase....................................1.80

90-0110 Dowel, barrel/crankcase 4 speed........use:-26-0650

90-0111 Cylinder stud......................................use:- 90-1440

90-0112 Crankcase oil filler plug & dipstick ...................8.25 alternative:- 70-7987 (plastic)

90-0115 Gearbox drain bolt.............................................3.20

90-0117 Clutch cover gasket 3 speed models................2.60

90-0121 Engine pinion tab-washer.................................0.65

90-0122 Clutch arm return spring..................................1.80

90-0124 Clutch cover screw 3"......................................1.80 

90-0125 Side cover screw.................................Out Of Stock

90-0130 Small end bush 125cc....................................10.90

90-0132 Clutch rod sleeve/bush....................................0.50

90-0134 Primary chain....................................use:- 19-8643

90-0135 Kickstart rubber................................use:- 68-3193 

90-0147 Mains oil seal L/H.............................................1.90

90-0152 Crankshaft shim set (5)....................................6.10

90-0172 Gearbox sprocket nut L/H thread.......................3.90

90-0246 Magneto points cam key ..................................2.20

90-0248 1/4 x 1/2" BSW cap head screw........................0.30

90-0259 Nut, generator .................................................2.90

90-0262 Fibre washer, drain bolt....................................0.15


90-0265 Exhaust ring nut D1-D7, D10 small bore.........31.00

90-0268 Gear change lever..........................................34.75

90-0273 Cylinder base gasket D1

(50mm between studs)..................................................1.30

90-0278 Piston ring set +020" 125cc..............................6.50

90-0284 Mains oil seal (early D1)...................................2.45

90-0283 Thrust washer, 3 speed clutch..........................4.35

90-0299/13 Front sprocket 13T.......................................8.75

90-0299/14 Front sprocket 14T.......................................8.95

90-0337 Piston kit std 125cc.........................................30.00

90-0338 Piston kit +020" 125cc....................................38.75

90-0340 Nut, crank/mainshaft........................................1.20

90-0353 Layshaft gear 19T...........................................38.00

90-0388 Piston kit +"040 125cc....................................38.45

90-0394 Piston rings +040" 125cc..................................6.35

90-0398 Piston kit +"060 125cc....................................38.45

90-0398/60 Piston rings +060" 125cc.............................6.45

90-047316T front sprocket, all Bantams 3/16 chain......12.00
90-0722 Cylinder base gasket .......................................0.85

90-0734 Piston ring set std D3.....................................14.20

90-0734/60 Piston ring set +060" D3............................16.45

90-0736 Base gasket  (55mm stud centres)...................1.15

90-0737 Gudgeon pin D3 150cc....................................6.15

90-0749 Oil seal, crankshaft mains................................1.95

90-0789 Std piston kit D3 150cc...................................73.00

90-0794 Piston ring set +020" 150cc.................Out Of Stock

90-0798 Circlip................................................use:- 90-5701

90-0800 Cylinder head gasket 125cc(52mm st)..............2.15

90-0801 Cylinder head gasket D3..................................1.95

90-0865 Piston ring set +040" 150cc............................15.80

90-0892 Kickstart lever....................................use:- 90-0966

90-0816 Cylinder head gasket 125cc 55mm studs.........1.95

90-0868 Piston kit +020" 150cc.....................................63.00

90-0871 Piston kit +040" 150cc.....................................95.00

90-0873 Piston Ass'y +060" D3 (Italian made)...............73.85

90-0966 Kickstart lever rigid small spine........................36.50

90-1143 Gear-change shaft 3 speed models ................22.85
90-1288 Gear-change return spring.................................3.40

90-1306 Cylinder head gasket D5/D7..............................2.25

90-1307 Cylinder base gasket 175cc...............................1.60

90-1311 Std piston rings (3)...........................................13.60

90-1312 Piston ring set +020" 175cc (set of three)........13.60

90-1313 Piston ring set +040" 175cc (set of three)........13.50

90-1314 Piston ring set +060" 175cc (set of three)........13.60

90-1318 Clutch friction plate..........................................6.25

90-1353 Piston kit +060" 175cc...................Use:-.....90-1466

90-1367 Clutch compression spring..................each.....1.45

90-1380 Barrel stud ........................................use:- 68-0222

90-1385 Bronze small end bush D7...............................9.15

90-1386 Gudgeon pin circlip 175cc...................each.....0.75

90-1393 Gudgeon pin (long)..........................................5.70

90-1394 Piston kit +020" 3 ring........................use:- 90-1462

90-1440 Cylinder stud all bantams.....................each.....4.30

90-1450 Chaincase screw 1/4 x 3/4................................0.95

90-1452 Cover screw 1/4 x 1-7/8"...................................0.90

90-1458 Small-end roller caged bearing 175cc..............3.65

90-1459 Piston kit std 3 ringed 175cc...........................42.25

90-1464 Piston kit +040" 3ringed..................................42.65

90-1466 Piston kit +060" 3 ringed.................................42.65

90-1515 Cylinder head gasket alloy 175cc.....................7.25

90-1585 Layshaft pinion 21T 3 speed...........................31.60

90-1593 Sleeved nut, stator unit....................................2.50

90-1595 Clutch cover gasket D10-D14 etc......................2.45

90-1597 Cylinder base gasket 175cc..............................1.50

90-1607 Stud, alternator................................................1.45

90-1608 Alternator stud, spacer set of 3.........................3.50

90-1620 Bush, layshaft Bantam/C15............................18.60

90-1622 Layshaft bush, closed end ..............................7.10

90-1642 Tab washer, quadrant.......................................1.20

90-1645 Gearchange shaft spindle..............................36.95

90-1649 Spacer, gear-change shaft ..............................2.40

90-1651 Selector plate 4 speed....................................14.75

90-1652 Backing washer 'O' ring....................................1.55

90-1654 Tab washer........................................use:- 90-0121

90-1666 Crankshaft 'O' ring...........................................0.60

90-1669 Oil filler plug & dipstick......................use:- 90-0112

90-1670 Woodruff key....................................................0.70

90-1673 Gearchange return spring................................3.25

90-1691 Layshaft pinion 21T 4 speed...........................65.25

90-1693 Mainshaft pinion 22T 4 speed.........................65.85

90-1694 Layshaft 18T 4 speed.....................................55.30

90-1696 Mainshaft pinion 26T 4 speed.........................25.00

90-1708/1 Folding kick-start lever small spline.............42.25

90-1717/8 Thrust bearing D14 etc................................10.20

90-1723 Indent spring 4 speed......................................1.25

90-1726 Nyloc nut, crankshaft.......................................1.20

90-1733 Bush, mainshaft D14......................................16.85

90-1736 Chainwheel washer..........................................1.15

90-3002 Exhaust sealing ring D1-3-5 &7........................3.20

90-3005 Silencer, D1 Flat type...................................150.00

90-3024 Front down pipe D1-3 Rigid (under footrest)...36.95

90-3033 Front down-pipe D1-3 plunger........................38.00

 

                                     **NB:-

  Some front pipes have been a bit tight on fitting, and      may need a small ''Tweak' to help them sit properly.*

90-3040 Silencer D1-D3 Fishtail end...................out of stock

90-3061 Silencer clip.....................................................3.75

D1 silencer cone end...................................................89.10

90-3070 Front downpipe D5-7......................................31.00

90-3108 Silencer D7 (plain cone-end)..........................94.50

90-3116 Silencer bracket...............................................6.50

90-3138 Silencer end piece ..........................................5.80

90-3139 Acorn nut, silencer end cone BSF thread.........2.60

90-3154 Front pipe hi-level, small bore D7-D10............35.30

90-9070 Exhaust 'C' spanner small bore........................8.95

BSA 300 Gasket set D1 1948-'53 (no head gasket)......15.45

BSA 301 Gasket set D1 ................................................14.75

BSA 302 Gasket set D3...............................................14.45

BSA 326 Gasket set D5, D7.........................................15.45

BSA 333 Gasket set D10 small bore exhaust...............13.95

BSA 336 Gasket set D14.............................................14.45

GB-7 Bearing rollers 1/4 x 1/4" Various..............each.....0.30

GS87 Breather disc, Triumph...........................................7.25

K432C Counter sunk mag cover screw...........................0.40

K432F Points retaining clip............................................1.25

NB135 Cap-head screw 1/4" x 3/4" BSW zinc plated......0.30

WW73115 Fibre washer, engine drain bolt.....................0.40


WW89202 Allen screw set B25, C25, SS......................16.40

WW89204 Allen screw set D10/D14.............................16.35

WW89206 Stainless steel engine Allen screw set

Whitworth threads D1 - D3...........................................16.50
WW89207 Allen screw set D7 (BSF thread).................16.40

WW89208 Allen screw set A50-A65 - 1968 BSF threads........................................................................16.65

WW89210 Allen screw set A7/A10 swinging arm Whitworth threads........................................................................19.35

WW91192 1/4 x 1/4" Roller................................each.....0.25

WW92006R Primary chain link...................................... 2.20

WW92010E Chain spring link 1/2 x 1/4" Elite chains......1.25

WW92010R Chain spring link1/2 x 3/16 Regina chains..2.20

WW93092 Exhaust clamp 1-1/2" ...................................2.25

083-1 110044 1/2 x 3/16 Link for Wipperman chain.........2.80

 



 

                            For enquiries or orders.

                                    Please email:-

                       [email protected]



Members Area

Newest Members

Recent Videos